MS90387H-2007 TOOL, HAND, ADJUSTABLE FOR PLASTIC....pdf

MS90387H 30 January 2007 SUPERSEDING MS90387G 28 March 1986 INCH-POUND DETAIL SPECIFICATION SHEET TOOL, HAND, ADJUSTABLE FOR PLASTIC AND METAL TIEDOWN STRAPS This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product specified herein shall consist of this specification sheet and MIL-DTL-81306. FIGURE 1. MS90387 Tool dimensions and configuration. AMSC N/A FSC 5120 Source: http:/ - Downloaded: 2008-06-10T04:18Z Check the source to verify that this is the current version before use. MS90387H 2 FIGURE 2. Ergonomic tool dimensions and configuration. TABLE I. Figure 1 and 2 dimensions.TABLE I. Figure 1 and 2 dimensions. MS Part number Figure A Max B Min B Max C Max D Max 1/ E Max Instruction field color MS90387-1 1 or 2 .65 .055 .065 1.00 N/A 4.63 Black MS90387-2 1 or 2 .85 .083 .090 1.34 1.20 4.63 Red MS90387-3 1 1.16 .015 .045 1.48 1.20 4.63 Blue MS90387-4 1 .85 .090 .100 1.34 1.20 4.63 Blue MS90387-5 1 .65 .055 .065 1.00 N/A 3.00 Black 1/ N/A Not applicable Source: http:/ - Downloaded: 2008-06-10T04:18Z Check the source to verify that this is the current version before use. MS90387H 3 TABLE II. Tool and plastic tiedown strap cross-reference. Tool Plastic Tiedown Strap Sizes MS part number Tension setting range (see note 4) MS part number Strap identification code Strap min tensile, pounds (reference) 1-3 MS3367-4, -26 MS3368-5 Min (Miniature) 18 3-5 MS3367-5, -27 Int. (Intermediate) 30 MS90387-1 MS90387-5 (See note 4) 6-8 MS3367-1, -2, -7, -23, -24, -29 MS3368-1, -2, -3, -4 Std (Standard) 50 1-4 MS3367-1, -2, -7, -23, -24, -29 MS3368-1, -2, -3, -4 Std (Standard) 50 MS90387-2 5-8 MS3367-3, -6, -8 to -18, -25, -28 Hvy (Heavy) 120 1-4 M23190/3-1 to /3-4 Std (Standard) 100 MS90387-3 5-8 M23190/3-5 to /3-9 Hvy (Heavy) 250 1-4 MS3367-3, -6, -8, -18 to -25, -28 Hvy (Heavy) 120 MS90387-4 5-8 MS3367-19 to -22 EH (Extra heavy) 250 REQUIREMENTS: 1. Finish: See MIL-DTL-81306. 2. Tools shall have no burrs, sharp edges or sharp corners. 3. The index line and eight tension station lines shall be clear and distinguishable. Increasing station line numbers shall represent increasing tension load (see note 2). 4. Instructions and part numbers shall have white or silver lettering on a field colored as specified in table I and shall be securely attached to the tool. Tension setting ranges correlated to the strap identification codes specified in table II shall be indicated on the tool (see note 3). 5. The handle shall be spring returned, shall facilitate grasping, and shall be colored same as the instructions field. Source: http:/ - Downloaded: 2008-06-10T04:18Z Check the source to verify that this is the current version before use. MS90387H 4 6. The tool tension setting shall not change during consecutive operations. 7. The tool shall tension and automatically sever the strap without detriment to strap performance as specified by SAE-AS23190. The tool shall be designed to cut the strap parallel with the strap head. 8. The entry edge(s) of the strap guide shall permit easy entry of the strap. 9. MS90387 shall be the only tools to be procured and stocked for government use to install plastic and metal tiedown straps. 10. For design feature purposes, this specification sheet takes precedence over procurement documents referenced herein. 11. Referenced documents shall be the issue in effect on date of invitations for bids, or request for proposal, except that referenced adopted industry documents shall give the date of the issue adopted. NOTES: 1. All dimensions are in inches. 2. Additional information regarding increasing tension direction (such as indicating arrows) may be added at manufacturers option. 3. The tension setting ranges are for typical wire bundle applications. Settings less or greater than the ranges specified may be necessary for special applications. 4. The compact tool - 5 is recommended for smaller handgrips. 5. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Source: http:/ - Downloaded: 2008-06-10T04:18Z Check the source to verify that this is the current version before use. MS90387H 5 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR Navy - AS Navy - AS Air Force - 11 (Project 5120-2006-003) Review activities: Navy - EC, OS, SH Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Source: http:/ - Downloaded: 2008-06-10T04:18Z Check the source to verify that this is the current version before use.