MIL-PRF-19500.394M-2008.pdf

MIL-PRF-19500/394M 15 July 2008 SUPERSEDING MIL-PRF-19500/394L 12 October 2007 PERFORMANCE SPECIFICATION SHEET * SEMICONDUCTOR DEVICE, TRANSISTOR, NPN, SILICON, POWER SWITCHING, TYPES: 2N4150, 2N5237, 2N5238, 2N4150S, 2N5237S, AND 2N5238S, JAN, JANTX, JANTXV, JANS, JANSM, JANSD, JANSP, JANSL, JANSR, JANSF, JANSG, JANSH, JANHCA, JANHCB, JANKCA, JANKCB, JANKCM, JANKCD, JANKCP, JANKCL, JANKCR, JANKCF, JANKCG, and JANKCH This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-19500. 1. SCOPE * 1.1 Scope. This specification covers the performance requirements for NPN, silicon, low-power, high voltage transistors. Four levels of product assurance are provided for each encapsulated device type as specified in MIL-PRF-19500 and two levels of product assurance are provided for each unencapsulated device type. Provisions for radiation hardness assurance (RHA) to four radiation levels is provided for JANTXV, JANS, JANHC, and JANKC product assurance levels. RHA level designators “M”, “D”, “P“, “L”, “R”, “F”, “G”, and “H” are appended to the device prefix to identify devices which have passed RHA requirements. 1.2 Physical dimensions. See figure 1 (TO- 5) and figures 2 and 3 (JANHC and JANKC). 1.3 Maximum ratings unless otherwise specified TA = +25C. Types PT (1) TA = +25C PT (2) TC = +25C R JA (max) (3) R JC (max) (4) VCBO VCEO VEBO IC TSTG and TJ 2N4150, S 2N5237, S 2N5238, S W 1.0 1.0 1.0 W 15 15 15 C/W 175 175 175 C/W 10 10 10 V dc 100 150 200 V dc 70 120 170 V dc 10 10 10 A dc 10 10 10 C -65 to +200 (1) For derating see figure 4. (2) For derating see figure 5. (3) For thermal impedance curve see figure 6. (4) For thermal impedance curve see figure 7. AMSC N/A FSC 5961 INCH-POUND Comments, suggestions, or questions on this document should be addressed to Defense Supply Center, Columbus, ATTN: DSCC-VAC, P.O. Box 3990, Columbus, OH 43218-3990, or emailed to Semiconductordscc.dla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil . The documentation and process conversion measures necessary to comply with this document shall be completed by 15 October 2008. Source: http:/ - Downloaded: 2008-08-19T05:34Z Check the source to verify that this is the current version before use. MIL-PRF-19500/394M 2 1.4 Primary electrical characteristics unless otherwise specified TA = +25C. hFE2 (1) hFE3 (1) Cobo |hfe| VBE(sat) (1) VCE(sat)1 Limits IC = 5 A dc IC = 10 A dc IE = 0 IC = 0.2 A dc IC = 5 A dc IC = 5 A dc VCE = 5 V dc VCE = 5 V dc VCB = 10 V dc VCE = 10 V dc IB = 0.5 A dc IB = 0.5 A dc 100 kHz f 1 MHz f = 10 MHz pF V dc V dc Min 40 10 1.5 Max 120 350 7.5 1.5 0.6 (1) Pulsed, (see 4.5.1). 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-19500 - Semiconductor Devices, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-750 - Test Methods for Semiconductor Devices. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Source: http:/ - Downloaded: 2008-08-19T05:34Z Check the source to verify that this is the current version before use. MIL-PRF-19500/394M 3 Dimensions Inches Millimeters Symbol Min Max Min Max Notes CD .305 .335 7.75 8.51 CH .240 .260 6.10 6.60 HD .335 .370 8.51 9.40 LC .200 TP 5.08 TP 6 LD .016 .021 0.41 0.53 7, 8 LL See notes 7, 8, 11,12 LU .016 .019 0.41 0.48 7, 8 L1 .050 1.27 7, 8 L2 .250 6.35 7, 8 P .100 2.54 5 Q .050 1.27 4 r .010 0.25 10 TL .029 .045 0.74 1.14 3 TW .028 .034 0.71 0.86 2 45TP 45TP 6 NOTES: 1. Dimension