ISO 15609-3-2004 金属材料焊接工艺的规范和评定.焊接工艺规范第3部分：电子束焊接.pdf

Reference numberISO 15609-3:2004(E)ISO 2004 INTERNATIONAL STANDARD ISO15609-3First edition2004-08-01Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 3:Electron beam welding Descriptif et qualification dun mode opratoire de soudage pour les matriaux mtalliques Descriptif dun mode opratoire de soudage Partie 3:Soudage par faisceau dlectrons ISO 15609-3:2004(E)PDF disclaimer This PDF file may contain embedded typefaces.In accordance with Adobes licensing policy,this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing.In downloading this file,parties accept therein the responsibility of not infringing Adobes licensing policy.The ISO Central Secretariat accepts no liability in this area.Adobe is a trademark of Adobe Systems Incorporated.Details of the software products used to create this PDF file can be found in the General Info relative to the file;the PDF-creation parameters were optimized for printing.Every care has been taken to ensure that the file is suitable for use by ISO member bodies.In the unlikely event that a problem relating to it is found,please inform the Central Secretariat at the address given below.ISO 2004 All rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical,including photocopying and microfilm,without permission in writing from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel.+41 22 749 01 11 Fax +41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2004 All rights reserved -,-ISO 15609-3:2004(E)ISO 2004 All rights reserved iii Foreword ISO(the International Organization for Standardization)is a worldwide federation of national standards bodies(ISO member bodies).The work of preparing International Standards is normally carried out through ISO technical committees.Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.International organizations,governmental and non-governmental,in liaison with ISO,also take part in the work.ISO collaborates closely with the International Electrotechnical Commission(IEC)on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives,Part 2.The main task of technical committees is to prepare International Standards.Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.Publication as an International Standard requires approval by at least 75%of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.ISO shall not be held responsible for identifying any or all such patent rights.ISO 15609-3 was prepared by the European Committee for Standardization(CEN)in collaboration with Technical Committee ISO/TC 44,Welding and allied processes,Subcommittee SC 10,Unification of requirements in the field of metal welding,in accordance with the Agreement on technical cooperation between ISO and CEN(Vienna Agreement).This first edition cancels and replaces ISO 9956-10:1996 which has been technically revised.Throughout the text of this document,read“.this European Standard.”to mean“.this International Standard.”.ISO 15609 consists of the following parts,under the general title Specification and qualification of welding procedures for metallic materials Welding procedure specification:Part 1:Arc welding Part 2:Gas welding Part 3:Electron beam welding Part 4:Laser beam welding Part 5:Resistance welding -,-ISO 15609-3:2004(E)iv ISO 2004 All rights reserved Contents page Foreword.v 1 Scope.1 2 Normative references.1 3 Terms and definitions.1 4 Technical content of welding procedure specification(WPS).3 4.1 General.3 4.2 Welding process.3 4.3 Related to the manufacturer.34.4 Equipment used.3 4.5 Related to the parent materials.3 4.6 Filler or other additional material(s).4 4.7 Joint design.4 4.8 Joint preparation.4 4.9 Jigs,fixtures and tooling.4 4.10 Welding position.4 4.11 Back and/or front support.4 4.12 Magnetism.4 4.13 Welding technique.4 4.14 Welding parameters.4 4.15 Pre and post weld heating.5 4.16 Operations after welding.5 Annex A(informative)Example of a Welding Procedure Specification for electron beam welding(process 51).6 -,-ISO 15609-3:2004(E)ISO 2004 All rights reserved v Foreword This document(EN ISO 15609-3:2004)has been prepared by Technical Committee CEN/TC 121,Welding,the secretariat of which is held by DIN,in collaboration with ISO/TC 44 Welding and allied processes.This European Standard shall be given the status of a national standard,